GATEWAY 6510GZ DRIVER FOR WINDOWS DOWNLOAD

After failing to completely clean the others, I added solder to all pins and put everything back together. I use high-tech rosin core silver-bearing solder from Radioshack with diameter 0. I have checked the RAM and it is not that. Then, if I sit on the sofa with the laptop on the cusion, it shuts off in XP only after a few minutes. You should solder the positive pin on one side of the motherboard but traces on both sides are connected by the sleeve inside the whole. Now, I am up and running. Now the AC adapter light is flashing.

Uploader: Makus
Date Added: 18 May 2008
File Size: 61.86 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 41135
Price: Free* [*Free Regsitration Required]

Gateway Drivers Download

Did I do something wrong? I need gateway 6510gz for an HP DC Jacks by Type. My question, is something on the laptop causing the AC adapters to fail? Gateway 6510gz models listed below may also use Jack 11, either will work in place of each other.

Zasilacze do laptopów – Szukaj części – Konfigurator QOLTEC

I am a complete newbie wrt soldering and stuff, but I went gateway 6510gz and bought all the equpiments suggested gateway 6510gz for under 20 pounds, and it took me about six hours to dissemble the laptop again following the tutorial here, fix the soldering and put it back together.

But, still, here I go. Any models listed below may also use Jack 15, depending on what the factory had available during manufacturing! Due to an error in shipping Dell sent me three batteries instead of one so I have plenty to charge and keep gateway 6510gz in power. I tried to solder it and gateway 6510gz solder sucker it off, but that was futile.

Could I have damaged the motherboard or the video gateway 6510gz But when I plug in the AC Adapter the led on the adapter goes out and get no power. Disconnect the LCD screen cable from the motherboard. The peg inside my computer broke, and I was about to try to replace it, but if you like do things kind of ghetto like me, I discovered an option.

I attempted to boot up my computer and the repair turned out to be no good. I have a question. Second, rotate gateway 6510gz screen so you can access screw holes.

Remember its not the users manual. Should I be using some sort of glue as well. Anyone have better ideas or comments? I am still trying to replace my Dell Latitude D jack. Your laptop shuts down because of overheating. The trick to fix it so you can forget it is to scrape the entire pad free of the green coating solder mask. My solution described in the gateway 6510gz post is to use a Dremel gateway 6510gz to carefully cut away a small part of the bottom of the plastic case that conceals the DC connector.

Bruce, Not all HP manuals have laptop disassembly instructions, I believe only newer models have it. Rob, Yes, all you need is three main parts: Gateway 6510gz, I am the only one with a Dell I work in a 3 people office where Gateway 6510gz use my personal laptop for work stuffso, no one can gateway 6510gz me test the adapters.

Or is the only problem in 6510ggz this that the solder is more likely to come off again? Are there several layers of tracing on one side gateway 6510gz the circuit board or is there just one on each side.

DC power jack repair guide

I replaced my dc jack and I tested the continuity and it beeps on my meter. I tried to turn it on and off to see if I could see any display but without success. I have a sony vgn, gateway 6510gz dc adapter was broken I replaced the part, it had no soldering involved. Is there software that will let the computer run without a windows enviroment?

If the power LED lights up but the laptop will not gateway 6510gz when you press the power button, there could be a problem with the memory. I have a Toshiba M30X laptop that had the common problem of a loose gateway 6510gz jack that takes a couple minutes of cord-wiggling to re-establish gateway 6510gz connection if it is unplugged, so it had been acting more like a desktop.

Well, I just removed a gateway 6510gz of the solder with the removal tool. Take your laptop to a professional repair shop instead. Test for continuity and for shorts before you apply power.

If the fuse is OK and motherboard receives power from the adapter but the laptop is still dead, most likely you gateway 6510gz a problem with the motherboard. I figured it was a gateway 6510gz with the AC adapter. This page is long but you can scroll down to view images of our products! The tip that came gateway 6510gz it is not sharp enough so I guess I have to buy a pencil tip for it. I was able to take it apart, reflow the solder: